Some degree of water loss in a swimming pool or spa is to be expected during the course of usage. Water loss in these structures normally happens in three main ways. These ways include through backwashing the filters, splash out, or through evaporation. For those who live in hot areas, the amount of water loss due to evaporation can be very high. This is worth knowing about Queen Creek pool service.
As water is lost through the methods named above, it is advisable to add a minimum of two inches of water per week to the structure. The need to add over two inches however, may indicate the existence if a leak. This is especially true if there is no other reason for the change in the speed of loss of water.
For example, it should be understood that the rate of evaporation may change with the season. Increased usage of the pool in the past few days may lead to an increase in the loss of water from the structure. If the season has not changed and the usage of the structure has remained the same recently yet water loss is happening faster, one should become suspicious.
However, before one goes a step further to call the local pool tech, it is important to confirm the suspicions first. There are a few techniques that one can use to confirm if actually a leak exists in the structure. To detect if a leak exists, one should start by checking the obvious. For instance, one must ensure that the leak is not happening at the equipment pads.
To make sure there is no leakage, one ought to have a close look at the filter, pump, pipe valves, and heater. One also has to check the ground surrounding the structure to make sure it is dry. The individual should walk around the pool/spa to check for any sunken areas or those that have been eroded. If nothing is out of place, it is time to move to the next step.
The other technique one can use to ascertain if there is a leak in the structure is marking the water level in the pool at the skimmer. One can do this using grease, a pencil, or tape. Afterwards, one should leave the structure for a duration of 24 hours before checking on the new level of water.
An ordinary pool should lose about a quarter an inch of water each day. In case the drop in the level of water is higher than a quarter an inch, this could mean that a leak exists. Another way is to use a bucket with water filled to a similar level as the level in the structure. The bucket ought to be placed on top of the steps used when entering the structure.
The bucket has to be given a duration of 24 hours, after which one should check it. If the level of water in the pool has gone below the height of water in the bucket, then this is confirmation of the presence of a leak. Because the water in both the structure and the bucket are subjected to evaporation, the rate of water loss ought to be the same.
As water is lost through the methods named above, it is advisable to add a minimum of two inches of water per week to the structure. The need to add over two inches however, may indicate the existence if a leak. This is especially true if there is no other reason for the change in the speed of loss of water.
For example, it should be understood that the rate of evaporation may change with the season. Increased usage of the pool in the past few days may lead to an increase in the loss of water from the structure. If the season has not changed and the usage of the structure has remained the same recently yet water loss is happening faster, one should become suspicious.
However, before one goes a step further to call the local pool tech, it is important to confirm the suspicions first. There are a few techniques that one can use to confirm if actually a leak exists in the structure. To detect if a leak exists, one should start by checking the obvious. For instance, one must ensure that the leak is not happening at the equipment pads.
To make sure there is no leakage, one ought to have a close look at the filter, pump, pipe valves, and heater. One also has to check the ground surrounding the structure to make sure it is dry. The individual should walk around the pool/spa to check for any sunken areas or those that have been eroded. If nothing is out of place, it is time to move to the next step.
The other technique one can use to ascertain if there is a leak in the structure is marking the water level in the pool at the skimmer. One can do this using grease, a pencil, or tape. Afterwards, one should leave the structure for a duration of 24 hours before checking on the new level of water.
An ordinary pool should lose about a quarter an inch of water each day. In case the drop in the level of water is higher than a quarter an inch, this could mean that a leak exists. Another way is to use a bucket with water filled to a similar level as the level in the structure. The bucket ought to be placed on top of the steps used when entering the structure.
The bucket has to be given a duration of 24 hours, after which one should check it. If the level of water in the pool has gone below the height of water in the bucket, then this is confirmation of the presence of a leak. Because the water in both the structure and the bucket are subjected to evaporation, the rate of water loss ought to be the same.
About the Author:
Get excellent tips on how to pick a Queen Creek pool service company and more info about a reliable company at http://www.neptunepoolsaz.com right now.
No comments:
Post a Comment